收藏本站
MAX16826
Programmable, Four-String HB LED Driver with
Output-Voltage Optimization and Fault Detection
Shunt Regulator
The MAX16826 has an internal 26V (typ) shunt regula-
tor to provide the primary protection against an auto-
motive load dump. When the input voltage is below
26V, the shunt voltage at IN tracks the input voltage.
When the input voltage exceeds 26V, the shunt regula-
tor turns on to sink current, and the voltage at IN is
clamped to 26V. During a load dump, the input voltage
can reach 40V, and the shunt regulator through the
resistor connected to IN is forced to sink large amounts
of current for up to 400ms to limit the voltage that
appears at IN to the shunt regulation voltage. The sink-
ing current of the shunt regulator is limited by the value
of resistor (R1 in Figure 1) in series with IN. There are
two criteria that determine the value of R1: the maxi-
mum acceptable shunt current during load dump, and
the voltage drop on R1 under normal operating condi-
tions with low battery voltage. For example, with typical
20mA input current in normal operation, 250mA load
dump current limit, 40V maximum load dump voltage,
the R1 value is:
For stable operation, the shunt regulator requires a min-
imum 10μF of ceramic capacitance from IN to GND.
V CC Regulator
The 5.25V V CC regulator provides bias for the internal
circuitry including the bandgap reference and gate dri-
vers. Externally bypass V CC with a minimum 4.7 μF
ceramic capacitor. V CC has the ability to supply up to
50mA of current, but external loads should be mini-
mized so as not to take away drive capability for inter-
nal circuitry. If IN is powered by a voltage less than
5.5V, connect V CC directly to IN.
Switch-Mode Controller
The MAX16826 consists of a current-mode controller
that is capable of operating in the 100kHz to 1MHz fre-
quency range (Figure 2). Current-mode control pro-
vides fast response and simplifies loop compensation.
The error amplifier compares the voltage at FB to 1.25V
and varies the COMP output accordingly to regulate.
The PWM comparator compares the voltage at COMP
with the voltage at RSC to determine the switching duty
V INMIN ? V INREG
R 1 = =
I Q
7 . 5 ? 5 . 5
20 × 10 ? 3
= 100 Ω
cycle. The primary cycle-by-cycle current-limit com-
parator interrupts the on-time if the sense voltage is
larger than 200mV. When the sense voltage is larger
than 270mV, the secondary gross current-limit com-
where V INMIN is the minimum operating voltage and
V INREG is the minimum acceptable voltage at IN.
Use the following equation to verify that the current
through R1 is less than 250mA under a load-dump con-
dition:
parator is activated to discharge the soft-start capaci-
tor. This forces the IC to re-soft-start preventing
inductor current runaway due to the delay of the prima-
ry cycle-by-cycle current limit.
The switch-mode controller also features a low current
shutdown mode, adjustable soft-start, and thermal
I LD = LD
V ? 26 V
R 1
V IN
40 ? 26
= = 140 mA
100
R1
IN
shutdown protection.
C4
+
-
5V
REFERENCE
MAX16826
Figure 1. Shunt Regulator Block Diagram
12
Maxim Integrated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX16835ATE+T IC LED DRIVR HIGH BRIGHT 16-TQFN
MAX16838AUP+ IC LED DRIVR HIGH BRIGHT 20TSSOP
MAX1698EUB IC LED DRVR WT/CLR BCKLGT 10MSOP
MAX17014EVKIT+ KIT EVAL FOR MAX17014
MAX17061AETI+T IC LED DRVR WHITE BCKLGT 28-TQFN
MAX17061ETI+T IC LED DRVR WHITE BCKLGT 28-TQFN
MAX17105ETG+T IC LED DRVR WHITE BCKLGT 24-TQFN
MAX17127ETP+ IC WLED DVR SIX STRING 20TQFN
相关代理商/技术参数
MAX16826ATJ+T 功能描述:LED照明驱动器 Prog 4-String HB RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16826ATJ+TC24 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE, FOUR-STRING HB LED DRIVER WITH OUTPUT-VOLTAGE - Tape and Reel
MAX16826BATJ/V+ 功能描述:LED照明驱动器 Prog 4-String HB RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16826BATJ/V+T 功能描述:LED照明驱动器 Prog 4-String HB RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16826BATJ+ 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE, FOUR-STRING HB LED DRIVER WITH OUTPUT-VOLTAGE - Rail/Tube
MAX16826BATJ+T 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE, FOUR-STRING HB LED DRIVER WITH OUTPUT-VOLTAGE - Tape and Reel
MAX16826EVKIT+ 制造商:Maxim Integrated Products 功能描述:EVAL KIT FOR THE MAX16826 - Boxed Product (Development Kits)
MAX16826-SMP 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE, FOUR-STRING HB LED DRIVER WITH OUTPUT-VOLTAGE - Tape and Reel